SS-APT cs-2462 09/01/06 page 1 of 2 features ? automatically adjusts sensitivity levels without the need for operator inter- vention or programming. sensitivity increases with heat. ? microprocessor-based, combination photo and thermal technology. ? addressable-analog communication. ? sleek, low-profile design. ? two-wire slc connection. ? sleek, low-profile design. ? rotary, decimal addressing (1 ? 99). ? addresses can be viewed and changed without the need for elec- tronic programmers. ? dual bi-color led design provides 360 viewing angle. ? built-in tamper-resistant feature. ? sealed against back pressure. ? constructed of off-white bayblend?, designed to commercial standards, and offers an attractive appearance. ? 94-5v plastic flammability rating. ? sems screws for wiring of the separate base. ? several base options, including relay, isolator, and sounder. ? remote test feature from the panel. ? built-in functional test switch acti- vated by external magnet. ? capable of heat-only alarm mode, enabled by a special command from the panel. smoke alarms are ignored. ? low-temperature signal at 45f +/? 10f (7.22c +/? 5.54c). listings listings and approvals below apply to the SS-APT acclimate tm multi-sensor low-profile intelligent addressable smoke detectors. in some cases, certain detectors may not be listed by certain approval agencies, or listing may be in process. consult factory for latest listing status. ? ul listed: file s1195. ? csfm approved: file 7272-1288:165. ? mea approved: file 275-02-e vol. iv. SS-APT acclimate? multi-sensor smoke detector low-profile, intelligent, addressable acclimate? is a trademark of system sensor. bayblend? is a registered trademark of bayer corporation. SS-APT in ss-b6 base 6937pho1.jpg description gamewell?s SS-APT accli- mate? detector is an intelligent, addressable, multi-sensing, low- profile detector designed for use with any 600 series smart scan tm slc panel. the acclimate? detector uses a combination of photoelectric and thermal sensing technologies that are designed to increase im- munity to false alarms. unlike traditional intelligent detectors, the acclimate? detector has a microprocessor in the detector head that processes alarm data. as a result, the acclimate? detector adjusts its sensitivity automatically, without operator intervention or control panel programming. areas where the acclimate? detector is especially useful include office complexes, schools, college campuses, manufacturing and industrial facilities, and anywhere else the use of a particular area may change. the acclimate? detector automatically adjusts its sensitivity to acclimate itself to the environment. installation the SS-APT plug-in detector uses a separate base to simplify installation, service, and maintenance. a special tool allows maintenance personnel to plug-in and re- move detectors without using a ladder. mount base on an electrical backbox at least 1.5" (3.81 cm) deep. suitable mounting back boxes include: ? 4.0" (10.16 cm) square box. ? 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box. ? single-gang box ( except for relay or isolator base) . ? with b501bh or b501bht base, use a 4.0" (10.16 cm) square box. ? with b224rb or b224bi base, use a 3.5" (8.89 cm) octagonal box, or a 4.0" (10.16 cm) octagonal or square box. notes: 1) because of the inherent supervision provided by the slc loop, end- of-line resistors are not required. wiring ?t-taps? or branches are permitted for style 4 (class ?b?) wiring. 2) when using relay or sounder bases , consult ss-li data sheet for device limitations between isolator modules and isolator bases. application note: the SS-APT detector has the unique ability to adjust sensitiv- ity according to the environment, based on heat and smoke levels. avoid installing these detectors in locations that are susceptible to rapid and high temperature changes. an example of an incorrect application would be near or in line with the output of a self-contained heater. detector spacing: gamewell recommends spacing detectors in compliance with nfpa 72. in low airflow applications with smooth ceilings, space detectors 30 feet (9.144 m). for specific information regarding detector spacing, placement, and spe- cial applications, refer to nfpa 72. system smoke detector application guide, docu- ment a05-1003, is available at systemsensor.com .
SS-APT cs-2462 09/01/06 page 2 of 2 gamewell-fci 12 clintonville road northford, ct 06472-1610 phone: 203-484-7161 fax: 203-484-7118 www.gamewell-fci.com a honeywell company ? 2006 gamewell-fci specifications and wiring information are provided for information only and are believed to be accurate. gamewell-fci assumes no responsibility for their use. data and design are subject to change without notice. installation and wiring instructions shipped with the product shall always be used for actual installation. for more information, contact gamewell-fci. specifications product line information wiring diagrams SS-APT : low-profile intelligent multi- smoke detector. must be mounted to one of the bases listed below. bases: ss-b6 : standard u.s. low-profile base, ul listing. b501bp : standard european flangeless base, pkg. of 10. b501bh : sounder base, includes b501 base above. b501bht : same as b501bh, but includes temporal sounder. b224rb : intelligent relay base. b224bi : intelligent isolator base. isolates slc from loop shorts. accessories: ra400z : remote led annunciator. 3 ? 32 vdc. fits u.s. single-gang electrical box. supported by ss-b6 and b501 bases only. smk400 : surface mounting kit provides for entry of surface wiring conduit. for use with b501 base only . rmk400 : recessed mounting kit. for use with b501 base only . smb600 : surface mounting kit for use with ss-b6. bck-200b : black detector covers, box of 10. m02-04-01 : test magnet. m02-09-00 : test magnet with telescope stick. sensitivity auto-adjusting levels 1 to 2, 2 to 3, and 3 to 4%/ft. fixed-sensitivity levels: 0.5, 1, 2, 3, and 4%/ft. size 2.1" (5.3 cm) high x 4.1" (10.4 cm) diameter installed in b501 base, 6.1" (15.5 cm) diameter installed in ss-b6 base. shipping weight 5.2 oz. (147 g). operating temperature 0c to 38c (32f to 100f). ul-listed velocity range 0 ? 4000 ft./min. (1219.2 m/min.), suitable for installation in ducts. relative humidity 10% ? 93% noncondensing. thermal sensing rating fixed-temperature setpoint 135f (57c). electrical specifications: voltage range 15 ? 32 volts dc peak. standby current (max. avg.) 250 a @ 24 vdc (without communica- tion); 360 a @ 24 vdc (one communi- cation every 5 seconds with led en- abled). loop resistance 40 ohms maximum; varies according to control panel used. refer to panel installation manuals. led current (max.) 6.5 ma @ 24 vdc (?on?). bases available: ss-b6: 6.1" (15.5 cm) diameter. b501: 4.1" (10.4 cm) diameter. b501bh or b501bht: sounder base assembly. includes b501 base. b224rb relay base: screw terminals: up to 14 awg (2.0 mm2). relay type: form-c. rating: 2.0 a @ 30 vdc resistive; 0.3 a @ 110 vdc inductive; 1.0 a @ 30 vdc inductive. dimensions: 6.2" (15.748 cm) x 1.2" (3.048 cm). b224bi isolator base: dimensions: 6.2" (15.748 cm) x 1.2" (3.048 cm). maxi- mum: 25 devices between isolator bases. xr2b : detector removal tool. allows in- stallation and/or removal of the SS-APT series detector heads from base in high ceiling installations. t55-127-000 : detector removal tool with- out pole. xp-4 : extension pole for xr2b. comes in three 5-ft. sections. detector guards: note: the following guards are not ul listed with the SS-APT. consult with lo- cal ahj. sti 9601 : low-profile, flush-mount smoke detector guard, wire. sti 9602 : low-profile, surface-mount, smoke detector guard, wire. sti 9609 : high-profile, flush-mount, smoke detector guard, wire. sti 9605 : high-profile, surface-mount, smoke detector guard, wire. sti 9604 : flush-mount heat detector guard, wire. sti 9610 : surface-mount heat detector guard, wire. sti-8200-ss : flush-mount stainless steel smoke detector guard. sti-8230-ss : surface-mount stainless steel smoke detector guard. address dial on back of detector. 4762wir1.tif
|
